Công ty IPCA phân phối bộ chuyển đổi quang camera, lắp đặt bộ chuyển đổi quang camera, bộ chuyển đổi quang camera ip, camera Wifi, bộ chuyển đổi quang camera Ai, IPCA đưa ra giải pháp tối ưu nhất cho hệ thống camera quan sát từ xa.
10/100Mbps Multi-mode Media Converter TP-LINK MC100CM
– Complies with 802.3u 10/100Base-TX, 100Base-FX standards
– Link Fault Passthrough and Far End Fault minimize the loss caused by link failure timely
– Provides switch configuration of Half-Duplex / Full-Duplex transfer mode for FX port
– Extends fiber distance up to 2km
– Auto negotiation of 10/100Mbps and auto MDI/MDIX for TX port
– Provide switch configuration of Half-Duplex / Full-Duplex transfer mode for FX port
1000Base-TX (UTP) to GBIC Media Converter D-Link DMC-805G-E
– This converter converts 1000BASE-T twisted-pair signals to 1000BASE-SX/LX multi-mode/single-mode fiber signals. Maximum fiber cable distance is 550 m for 1000BASE-SX and 20 km for 1000BASE-LX. 1 RJ-45 twisted-pair port and 1 SFP port (mini GBIC) are provided.
100Base-TX to 100Base-FX (LC) Single-mode Media Converter D-Link DMC-F20SC-BXD/E
Media converters DMC-F20SC-BXD and DMC-F20SC-BXU perform conversion of interfaces ‘twisted pair – a single mode optical fiber cable according to one’ for the Ethernet 10/ 100BASE-TX and 100BASE-FX networks. Devices can simultaneously transmit and receive signals at wavelengths between 1310 nm and 1550 nm in a single optical fiber at a distance of 20 km.
100Base-TX to 100Base-FX (LC) Single-mode Media Converter D-Link DMC-F20SC-BXU/E
D-Link’s Standalone Media Converters turn an Ethernet connection into fiber, allowing for ultra-fast long distance connections. Installation of a Standalone Media Converter is simple, and allows you to tap into fiber speeds with ease. Instead of requiring an investment in an entire chassis, the standalone series is able to provide the same high-quality conversion on a unit-by-unit basis. The standalone nature of these means that you can use save space and cut costs while still extending your network over long distances up to 60 km on a fiber-optic line. In addition to all models supporting 10/100 Mbps Half/Full-duplex, the DMC-G01LC also allows for 1000 Mbps Full-Duplexing, letting you truly maximize your network’s potential.
100Base-TX to 100Base-FX (SC) Single-mode Media Converter D-Link DMC-F02SC/E
– 100Base-TX to 100Base-FX (SC) Single-mode Media Converter (2km) (Stand-Alone).
– This media converter converts the signal from the standard 10BASE-T/ 100BASE-TX Fast Ethernet on twisted pair at signal 100BASE-FX Fast Ethernet standard for multimode fiber optic cable. Maximum Fiber Optic Cable Length: 2 km. The apparatus 1 is equipped with a port RJ-45 twisted pair and one optical port. The DMC-F02SC used SC connector.
100Base-TX to 100Base-FX (SC) Single-mode Media Converter D-Link DMC-F15SC/E
D-Link’s Standalone Media Converters turn an Ethernet connection into fiber, allowing for ultra-fast long distance connections. Installation of a Standalone Media Converter is simple, and allows you to tap into fiber speeds with ease. Instead of requiring an investment in an entire chassis, the standalone series is able to provide the same high-quality conversion on a unit-by-unit basis. The standalone nature of these means that you can use save space and cut costs while still extending your network over long distances up to 60 km on a fiber-optic line. In addition to all models supporting 10/100 Mbps Half/Full-duplex, the DMC-G01LC also allows for 1000 Mbps Full-Duplexing, letting you truly maximize your network’s potential.
14-Slot Rackmount Chassis TP-LINK TL-MC1400
The TL-MC1400 14-Slot Rack-mount Chassis is specially designed to accommodate 14 TP-LINK‘s Media Converters for central power supply, saving space and power cables. Continuous operation is of great importance to fiber communication, so the chassis is equipped with optional redundant power supply and Hot-Swapping function which allows installing/removing the converter/power supply without powering off the chassis. Moreover, to stabilize the performance and extend the lifetime, two cooling fans are installed internally. Together with MC series Gigabit / Fast Ethernet media converters, TL-MC1400 is the ideal solution for your media conversion network.
DMC-1000 D-Link DMC-1001 Redundant Power Supply Unit for
– Intended for use with the DMC-1000 chassis, this redundant power supply unit acts as a fail-safe against power failure.
– The DMC-1001 is a hot swappable redundant power supply that is designed for use in the DMC-1000.
Gigabit Single-mode SFP Media Converter TP-LINK MC220L
The MC220L is a media converter designed to convert 1000BASE-SX/LX/LH fiber to 1000Base-T copper media or vice versa. Designed under IEEE802.3ab 1000Base-T and IEEE802.3z 1000Base-SX/LX/LH standards, the MC220L is designed for use with multi-mode/single-mode fiber cable utilizing the LC-Type connector. It works at 850nm on both transmitting and receiving data when adopting multi-mode fiber and 1310nm on both transmitting and receiving data when adopting single-mode.
Media converter D-Link DMC-1910R-A9A
-1000Base-TX to 1000Base-LX Single Fiber Media converter (Tx: 1310μm; Rx: 1550μm, Single-mode, 15km).
-The D-Link DMC-1910R Fiber Media Converter converts 1000BASE-T copper Gigabit signals to 1000BASE-LX fiber Gigabit signals.
-This allows you to connect longer distance fiber cables between two devices that are designed only for shorter distance Cat. 5 twisted pair cable.
-The DMC-1910R converts 10/100Mbps 10BASE-T-100BASE-TX Fast Ethernet twisted pair signals to 100BASE-FX single-mode signals up to 15 km apart.
-This media converter supports maximum 15 km fiber cable distance.
Media converter D-Link DMC-1910R-E
– 1000Base-TX to 1000Base-LX Single Fiber Media converter (TX: 1310μm; RX: 1550μm, Single-mode, 15km).
– Up to 15 km Single-Mode Fiber Cable Distance.
– Single Fiber Strand for Transmission/Reception.
– Full Duplex operation.
– 802.3x Flow Control Support.
– Manageable Through Intelligent Chassis System.
– LLR (Enable/Disable), Fiber (Auto-Negotiation/Manual) Functions.
– Installable as Stand-Alone Device or in Rack-Mount Chassis.
Media converter D-Link DMC-1910T-A9A
-1000Base-TX to 1000Base-LX Single Fiber Media converter (TX: 1550μm; RX: 1310μm, Single-mode, 15km).
-The DMC-1910T/A9A converts 10/100Mbps 10BASE-T-100BASE-TX Fast Ethernet twisted pair signals to 100BASE-FX single-mode signals up to 15 km apart.
-1 RJ-45 twisted-pair port and 1 fiber port (SC connector) are provided.
Media converter D-Link DMC-1910T-E
– 1000Base-TX to 1000Base-LX Single Fiber Media converter (TX: 1550μm; RX: 1310μm, Single-mode, 15km).
– The D-Link DMC-1910T/E Fiber Media Converter converts 1000BASE-T copper Gigabit signals to 1000BASE-LX fiber Gigabit signals. This allows you to connect longer distance fiber cables between two devices that are designed only for shorter distance Cat. 5 twisted-pair cable.
Media Converter D-Link DMC-300SC
DMC-300SC converts 10/100Mbps 10BASE-T/100BASE-TX Fast Ethernet twisted-pair signals to 100BASE-FX Fast Ethernet multi-mode fiber signals. Maximum fiber cable distance is 2 km. 1 RJ-45 twisted-pair port and 1 fiber port are provided.
Media Converter D-Link DMC-300SC-E
-10/100Base-TX (UTP) to 100Base-FX (SC) Multi-mode 2km Fiber Media Converter (Usable in DMC-1000 Chassis).
-The DMC-300SC/E by D-Link® is a media converter designed to connect 10BASE-T/100BASE-TX copper to 100Base-FX fiber media and vice versa. Based on the IEEE 802.3 and 802.3u standards, the DMC-300SC/E is designed for use with multimode fiber cable utilising the SC-Type connector.
Media Converter D-Link DMC-515SC-E
– 10/100Base-TX (UTP) to 100Base-FX (SC) Single-mode 15km Fiber Media Converter (Usable in DMC-1000 Chassis).
– The DMC-515SC convert 10/100Mbps 10BASE-T/100BASE-TX Fast Ethernet twisted-pair signals to 100BASE-FX Fast Ethernet single-mode fiber signals.
– 1 RJ-45 twisted-pair port and 1 fiber port (SC connector) are provided.
– Supporting maximum 15 km fiber cable distance.
Hiển thị 1–16 của 32 kết quả